No
|
Name
|
Description
|
Part
number
|
Manufacturer
|
1
|
Transmitter
|
-
Type:TWW 103-M1
- Two Analog output (Current):
+ 4 to 20mA, max. load
500 Ohm
+ 4 to 20mA, max. load 25
Ohm (serves for positioning of the proximity transducer )
+ The characteristic is in
inverse proportion 0 to 10 mm is equal 20 to 4 mA.
- Ambient temperature range: 0 to + 70°C
- Power consumption: max. 80 mA
- Power supply nominal: +24 V DC (18 – 30 V), galvanically separated.
- Protection class: IP 67
|
|
Meggitt
|
2
|
Proximity
Transducer
|
-
Type:WW 018 - 24x1,5 - 200 - 05 - MS
- The Static Measuring range is 10 mm.
- Ambiente temperature Range: -20 bis +145 °C
- Ingress Protection Rating: IP67
- Cable length: 5 m
- Measuring Range: 2 bis 12 mm
- linearity Deviation : ≤ ±2%
|
|
Meggitt
|
3
|
Piezoelectric
Accelerometer
|
-
Type: CA901
- Input power requirements : None
- Signal transmission : 2 pole system insulated from casing, charge output
- Signal processing : Charge converter
- Sensitivity (at 120 Hz) : 10 pC/g ±5%
- Dynamic measuring range (random) : 0.001 g to 200 g peak
- Overload capacity (spikes) : Up to 500 g peak
- EC type examination certificate : LCIE 08 ATEX 6017 X II 1 G
(Zones 0, 1, 2)
Ex ia IIC T6 to T710
- Cable length 3.5 m
|
Ordering
Number
144-901-000-282
|
Meggitt
|
4
|
Signal
conditioner
|
-Power
supply to IPC 704:
+ Voltage : 18 to 30 VDC
+ Current : 25 mA (max.)
- IPC 704 for sensors using standard piezoelectric materials
(244-704-000-042)
- Linearity error : ≤ 0.2 %
- Temperature stability : 100 ppm / °C typical
- 2-wire current transmission.
Ordering information:
- ENVIRONMENT: A1: Standard.
- TRANSFER UNIT: B01: Input: pC/g
Output: µA/g
- INPUT SENSITIVITY: C10: 10 pC/g
- OUTPUT SENSITIVITY: D50: 50 µA/g
- HP FILTER: E2: 2 Hz
- LP FILTER: F10000: 10000 Hz
- INSTALLATION: G0: Signal conditioner only
- INPUT CABLE FITTING: H0: NO HOLE
- OUTPUT CABLE FITTING: I0: NO HOLE
|
PNR:
244-704-000-042
A1-B01-C10-D50-E2-F10000-G0-H0-I0
|
Meggitt
|
5
|
Galvanic
Separation Units
|
-Type:
GSI 130
-Supply voltage (to GSI) : +24 V ±5%
-Ripple (100 Hz) : 100 mV pp max.
-Consumption:
No load : Approx. 20 mA
20 mA load : Approx. 60 mA
Short-circuit : Max. 120 mA
-Output voltage (to conditioner):
No load : 18 V ±1 V
20 mA : 16 V ±1 V
-Short-circuit current : 60 mA
-Pass-band : DC to 10 kHz ±0.5%, -1 dB at 20 kHz
-Transfer function : 1 V/mA factory set (potentiometer P1)
-Temperature drift : <200 ppm/°C
-Linearity : ±0.5% over dynamic measuring range
-DC signal component : Adjustable by
(to UVC) potentiometer P2
Umin. = +2 V
Umax. = power supply
(+24 V ±5%) - 2.5 V
|
PNR:
244-130-000-20
|
Meggitt
|
6
|
Extension
Cable
|
|
PNR:
922-153-000-202/5000
|
Meggitt
|
7
|
Proximity
transducer
|
-Type:TQ402
-Rang: 0.4-4.4mm
-Environment: Standard
-Body thread: M10x1
-Body length: 072mm
-Unthreaded length:0mm
-Integral cable length:10m
-Cable: Flexible hose with FEP sheath
-Flexible hose length: 10m
-Total system length:10m
Characteristics:SLV3210013; Design Group:MBBGH10000-A00/G050/H13F12K29;
Material No:PB0000044720 / A2A50146303
|
Ordering
number:111-402-000-013-A1-B1-C072-D000-E100-F2-G100-H10
|
Meggitt
|
8
|
Machinery
protection card
|
-
Number of inputs : 4 per MPC 4 card
- DC range : 0 to +20 V or 0 to -20 V
- AC range : Max. ±10 V
- Common mode voltage range : -50 V to +50 V
- CMRR : > 60 dB at 50 Hz
- Crosstalk : -72 dB
- Input impedance : 200 kΩ
- Current input range
• DC signals : 0 to 25 mA
• AC signals : Max. ±8 mA
- Analog AC frequency band : 0.1 Hz to 10 kHz
- Analog frequency band for throughput to
other cards and buffered AC outputs
: DC to 60 kHz (-3 dB)
- Current measuring resistor : 324.5 Ω
|
Ordering
Number.: 200-510-071-113
|
Meggitt
|
9
|
Vibration
Switch
|
-
3171MR Electro-mechanical vibration switch with manual reset.
- Performance: Set level range 0.5 to 9g peak acceleration.
- Switch rating: Resistive load - AC 5A 250V, DC 5A, 30V.
- Temperature range: -45 to +85 C.
- Ingress protection rating: IP67
- Type: Weatherproof
- Contacts Material: Gold
- Poles: Single Pole
- Reset: Manual Reset
- Pre-Set: Factory Set
|
Order
code: 8000-000
|
Meggitt
|
10
|
Proximity
transducer
|
-
Type: TQ402
- Protection rating : The entire transducer assembly is rated IP68
- Environment: Standard
- Body thread: M10x1
- Body length: 72mm
- Integral cable length: 5.0 m ± 500 mm
- Cable: Flexible hose with FEP sheath
- Flexible hose length : 5m
- Total system length: 5m
|
Ordering number: 111-402-000-013-A1-B1-C072-D000-E050-F2-G050-H05
|
Meggitt
|
11
|
Piezoelectric
Accelerometer
|
-
Type: CE680 M511
+ Operating
- Sensitivity (at +25 °C) : 100 mV/g ±5%
- Dynamic range : 80 g
- Transverse sensitivity (maximum) : 5% of axial
- Linearity : 1% up to full scale
+ Electrical
- Input supply current : 2 to 10 mA
- Supply voltage for current source : 18 to 30 VDC
- Bias output voltage : 12 VDC
+ Environmental
Temperature range : −55 to +120 °C
+ Physical
- Sensing element design : PZT ceramic / shear
- Weight (nominal) : 90 g
- Case material : 316L stainless steel
- Mounting : 1/4 - 28 UNF tapped hole
|
Ordering
number: 444-680-000-511
|
Meggitt
|
12
|
Signal
conditioner
|
-
Type: IQS450
- Environment: Standard
- Measuring range: 4mm
- Sensitivity: 4 mV/ µm
- Total system length: 5m
- Installation: Signal conditioner only
- Standard target material: VCL 140
- Supply ( Voltage output, 3-wire configuration)
+ Voltage : −20 to −32 V
+ Current : −13 mA ± 1 mA (−25 mA max.)
- Voltage output, 3-wire configuration
+ Voltage at min. gap : −1.6 V
+ Voltage at max. gap : −17.6 V
+ Dynamic range : 16 V
|
Ordering number:
204-450-000-002-A1-B23-H05-I0
|
Meggitt
|
13
|
Pressure Transmitter
|
- Model: 3051T
- Power supply: 10.5 –42.4 Vdc
-Pressure type: Gage
- Pressure upper range limit - configurable description: 800 psi (55,2 bar)
- Transmitter output: 4–20 mA with Digital Signal Based on HART Protocol
- Process connection style: G1/2 A DIN 16288 Male (Available in SST for Range
1–4 only)
- Isolating diaphragm : 316L SST
- Process connection wetted parts material: 316L SST
- Sensor fill fluid: Silicone
- Housing material: Polyurethane-covered Aluminum
- Conduit entry size: M20 1.5 (CM20)
- Mounting bracket: Bracket for 2-in. pipe or panel mounting, all SST
- Product certifications: ATEX Type n Certification and Dust
- Display type: LCD display
|
Ordering Information:3051TG3A2C21BB4N1M5
|
Emerson
|
14
|
Pressure Transmitter
|
- Power supply: 10.5 –42.4 Vdc
-Pressure type: Gage
- Pressure upper range limit - configurable description: 4000 psi (275,8 bar)
- Transmitter output: 4–20 mA with Digital Signal Based on HART Protocol
- Process connection style: G1/2 A DIN 16288 Male (Available in SST for Range
1–4 only)
- Isolating diaphragm : 316L SST
- Process connection wetted parts material: 316L SST
- Sensor fill fluid: Silicone
- Housing material: Polyurethane-covered Aluminum
- Conduit entry size: M20 1.5 (CM20)
- Mounting bracket: Bracket for 2-in. pipe or panel mounting, all SST
- Product certifications: ATEX Type n Certification and Dust
- Display type: LCD display
|
Ordering Information:3051TG4A2C21BB4N1M5
|
Emerson
|